نسل جدید عایق پلیمری ویژه آب بندی بامها و سرویس ها ISONEM ROOF

عایق پیلیمری ویژه آب بندی پشت با مها و سرویس با کیفیت بالا و اقتصادی


ISONEM ROOF is a waterproofing coating for roof and terraces, polyurethane resin based, liquid applied, two components, fully adhered, forming
very high coatings featuring very high chemical and physical resistance. The product has perfect UV resistance. It can be applied in thick layers to
protect the metal and concrete surfaces against the chemical and physical outside impacts.
USING AREAS: A long lasting coat is available to use on roofs in industrial plants, factories, refinery plants and particularly, chemicals factories,
laboratories, automotive industry fields, purification facilities, metal and concrete ROOF and walls.
ADVANTAGES: •Easy to apply •Durable, even at low temperatures •Excellent adhesion to the substrate •No seams or joints •Waterproof •Crack
bridging •Can colour match •Easy to clean •Excellent abrasion and wear resistance.
APPLICATION: Roller, brush, airless spray (It can be spray applied to ensure quick application, consistent appearance and a durable finish)
•MIXTURE RATIO: 4,2 kg polyurethane coat + 0,3 kg hardener: 4,5kg(A+B) •MIXTURE DENSITY: 1.15-1.60 gr/ml (mixture) •COLOR: It can be
produced in any color upon request. •APPEARANCE: Semi gloss 70 – 80 gloss / 60° •DUST FREE TIME: 1 hour. •TOUCHING DRY: 2 - 3 hours.
•COMPLETE DRY: 7 days.
FOR THE CONCRETE SURFACES: Surface must be clean, dry and free from all traces of loose material, old coatings, curing membranes, release agents,
laitance, oil and greases etc. Substrate compressive strength should be at least 25 MPa, cohesive bond. Structurally unsound layers and surface
contaminants must be mechanically removed by abrasive blasting, blasttracking or grinding. All dust, oil, dirt and surface residues should be removed
thus the concrete surfaces should be completely dry and clean. The drying period for the initial concrete surfaces is 21 days then the application can be
done,
FOR THE STEEL AND METAL SURFACES: The metal surfaces should be purified from any kind of oil, dust, rust and similar materials that may prevent
the paint to be fixed to the surface, if there is polyurethane paint on the surface previously and it is not possible to remove it then the surface of the
coat should be emeried and cleaned with solvent.
PREPARATION OF THE MIXTURE: A+ B Components. First the polyurethane is mixed for a few seconds then the hardener B component is added into
the coat and mixed thoroughly until the mixture will be shaped homogenous. The mixture ratio should be 4,2:0,3. The materials should be mixed
depending on the ratios strictly.
APPLICATION OF THE MIXTURE: The mixture is applied onto the surface in single layer by using a brush and airless spraying equipment, if the
thickness is required, the second layer should be applied immediately after the first layer got dried within 24 hours thus the best adhesion is ensured
among the middle layers. The application should be done into the same direction every time. The pre drying is realized for 2-3 hours at 20°C degree.
The hardening occurs within 9-10 hours. The complete hardening and physical, chemical resistance start after 7 days.
CLEANING: Clean all tools and equipment immediately after use with ISONEM PU THINNER Cleaner. Once hardened, the material can only be
removed mechanically. Wash hands and skin thoroughly in hot soapy water.
LIMITS ON APPLICATION: Do not apply when surface temperature is less than 3°C above dew point. Minimum substrate temperature +10°C.
Maximum substrate temperature +25°C. Maximum relative humidity 70%. Apply ISONEM ROOF surfaces those with moisture content less than 4%.
The moisture content must remain at or below 4% for the duration of the cure period. Where moisture content of the slab is greater than 4%, ISONEM
EP is recommended as a temporary moisture barrier.
HANDLING PRECAUTIONS: Avoid contact with the skin, eyes and avoid breathing it’s vapour. Wear protective gloves when mixing or using. If
poisoning occurs, contact a doctor or Poisons Information Centre. If swallowed, do NOT induce vomiting. Give a glass of water. If skin contact occurs,
remove contaminated clothing and wash skin thoroughly. If in eyes, hold eyes open, flood with warm water and seek medical attention without delay.
2 CONSUMPTION: 1 kg/m (500 microns – 1 mm thickness, In one layer)
STORAGE: 6 Months in original and closed package.
PACKAGE: Polyurethane 4,2 kg + hardener 0,3 kg; Total: 4,5 kg or Polyurethane 16,8 kg + hardener 1,2 kg; Total: 18 kg

نظرسنجی


دریافت کاتالوگ ها و فرم ها